Phan 32 #1 Posted Thursday at 05:53 PM Hello - I picked up 1075 recentlly with no key. I have tried with all keys that used for 865 and C, B, and 300 series, but it cannot ne inserted. Looking at the manual - it said the swich 4988. Anyone knows and where I can get the key. Thanks Share this post Link to post Share on other sites
gwest_ca-(File Mod) 11,669 #2 Posted Thursday at 06:15 PM Did you see these pictures? Click on the switch. Share this post Link to post Share on other sites
953 nut 61,682 #3 Posted Thursday at 11:18 PM (edited) 5 hours ago, Phan said: Hello - I picked up 1075 recentlly with no key. I have tried with all keys that used for 865 and C, B, and 300 series, but it cannot ne inserted. Looking at the manual - it said the swich 4988. Anyone knows and where I can get the key. Thanks Is the switch the factory original or could it have been replaced by a previous owner the past six decades? If it looks like the one shown in the manual Gary put up and the regular mower key won't fit it may be a Snoopy Key. Tractor Supply or a John Deere dealer may have some. Edited Thursday at 11:21 PM by 953 nut fat finger 1 Share this post Link to post Share on other sites
Achto 29,674 #4 Posted Thursday at 11:55 PM Cole Hersee key. https://www.amazon.com/R30074-B17575-Ignition-Ferguson-Terramite/dp/B07NRS68MT/ref=sr_1_4 Share this post Link to post Share on other sites
Phan 32 #5 Posted yesterday at 03:06 AM Hello All! Thank you! The switch has been replaced. I found it in the amazon is matching the switch on the tractor. I ordered it and will arrive tomorrow. https://www.amazon.ca/dp/B093PDJRSF? ref=ppx_yo2ov_dt_b_fed_asin_title But the engine cease - cannot turn by hand. Share this post Link to post Share on other sites
953 nut 61,682 #6 Posted yesterday at 10:23 AM The switch you have purchased is intended to operate with a solenoid. It is only rated at 30 amps and your starter will draw about 50 amps. Do you have a solenoid? 1 Share this post Link to post Share on other sites
Retired Wrencher 5,988 #7 Posted yesterday at 10:33 AM Richard is correct. If you want to bring it back to original I just pick up an original type key from wheel horse parts and more.com. This is this switch works with the start GEN tractors. I hope everything works out. Just take your time. 1 Share this post Link to post Share on other sites
Phan 32 #8 Posted yesterday at 02:42 PM 4 hours ago, 953 nut said: The switch you have purchased is intended to operate with a solenoid. It is only rated at 30 amps and your starter will draw about 50 amps. Do you have a solenoid? No selenoid. Share this post Link to post Share on other sites
Phan 32 #9 Posted yesterday at 02:45 PM 4 hours ago, Retired Wrencher said: Richard is correct. If you want to bring it back to original I just pick up an original type key from wheel horse parts and more.com. This is this switch works with the start GEN tractors. I hope everything works out. Just take your time. I will consider it. I hope I can crang the engine - it seiges now. Share this post Link to post Share on other sites
Phan 32 #10 Posted yesterday at 03:23 PM Dear All, I fount a great post / discussion / comments on 1075 - it teaches me a lot. Share this post Link to post Share on other sites
Retired Wrencher 5,988 #11 Posted 7 hours ago (edited) Give it a good look take notes and I think things will turn ok. Don’t be afraid to ask questions as you go. Edited 7 hours ago by Retired Wrencher Share this post Link to post Share on other sites
