Leaderboard

Selling this 314-H with only 138 hours. PO only used it to push snow on his short drive. It never even had a belt on the pto until I mounted a deck on it last summer. No attachments included. I will drive a reasonable distance (say about 4 hours round trip). I am not going to the big show but if you can work out a way to get it there I can hold it until then. Full documentation and some extras included. I would consider a trade but you would really have to tweak my interest. Something is screwed up with loading pictures right now so only one for now. The others errored out and this one took about 15 minutes to load.

Several of these 8-3900 clone hydro foot control pedal kits are available. Wheel Horse 8-3900 clones. Durable powder coat finish. $160.00 plus shipping.

36" Rear Discharge Mower - Rehabbed deck including Shell sand blast rust cleaning, primer paint and top coat, 3 new blades, new belt, 3 Spindles rebuilt with 6 new bearings, 2 new ouitside pulleys, new wheels, new front roller, added new center pulley reinforcement plate, 4 new lift carriage bumpers, new decals, misc new hardware. As option: pair of 2 new OEM belt/pulley covers at $40 (some minor surface blemishes ) . Deck Sold "As Is". No returns, Cash pick up Poughkeepsie NY area, no holds. First come basis. Please send message for questions or to arrange pick up.

A nice 867. Refreshed & re-ringed K181 service motor starts & runs perfect. Fresh transmission oil & magnetic drain plug. Headlight lens a perfect original. Cigar lighter does not work. All new fuel lines. Steering wheel bushed at the dash. Hitch pin removed, cleaned & zerk added. Entire tractor gone thru. Can deliver to the Big Show or have in southern mid Michigan in April.

1995 Model 520 H, serial #73501, 20hp Onan, hydrostatic transmission (in-op), 982 hrs, 60in. mower mounts under or on front, 36in. rototiller, hydraulic lift, dual wheel option, 4 rear heavy tread tires mounted, 2 rear turf tires mounted, complete rear 40lb. wheel weight kit and mounting hardware, extra belts and accessories for all attachments. All works EXCEPT the hydrostatic transmission, it failed 03/2026.

This one right now is one of a kind. 6/4 thickness made from mahogany. It's old stock that came from Gibson guitars. anyone interested PM me

Getting ready to retire after decades of rebuilding Kohler engines. This is a K321 wheel horse spec long block plus the pan, head valve breather assembly. This engine has been torn down to the bare block cleaned and Bored .010 over, crank ground .010, valve seats ground, head decked. New piston, rings, rod, valves, guides, seals and gaskets. Located in Mechanicsville, VA. 800.00 no core required. Photos of the rebuild are available if requested.

This has been sitting in my garage for 3 years and at this point I don't think I'll get around to putting in the time that it deserves to restore it. I'd love to see it go to someone who has the ability to restore it. I haven't started it so don't have too much insight into functionality. Will do my best to answer any questions... but eager to make some more room in the garage so happy to see it go.

For Sale - Charger 9 with hydro static drive and snow blade with frame. Photo is from a few years ago. Since then I replaced the piston and rod. Reinstalled the engine but never got it up and running. Hood and fuel tank are off as well as the sheet metal floor board. Snow blade and frame are separated from tractor. Have original seat (upholstery is very bad). My Mom bought this tractor in the mid 60's and my brothers and I mowed our two acres with it until we replaced it with at 312-8 in the 90's Would like to see it go to someone who wants to get it running or needs parts. It has the Tecumseh 10HP horizontal shaft engine with magneto. Hydro static drive. No mower deck. Tire Chains. Location NE Ohio

SOLD: I put it away in December, ran fine, no smoke, didn't use oil. In February it wouldn't start, it had fuel, air, and spark, might be valve issue. I took to a small engine shop and they said it was .003 out of round/taper, but it ran good before. They disassembled the engine and told me it was going to cost way more than I wanted to spend so its for sale to anyone wanting to reassemble the engine or repower it. I has a rear 3 point, rear PTO, manual front PTO clutch, seat, both lift cylinders, hood, grille with working lights, rear tires and wheels are like new. If no ones interested I'll part it out on eBay

This is an original 520-8. It was sold and serviced at Lincoln Rental in Rockford illinois. It comes with a 48" mower deck and 48" front blade and a Snow blower. It has 645 hrs on the hour meter. Price is OBO. Only 225 were made.

Solid old 32” deck. Missing the side guards and a pulley. Spins free and smoothly. Decent blades. $75 or make an offer. Pickup in Andover Ct.

Looking for a 1961 suburban 551 frame. Please let me know what ya got and we're your at. Thanks in advance

NOS hood for long frame 60s tractor. Been sitting around many years but never been installed on tractor. $50 located in South Haven, MI

Starts runs and drives in all gears, hydraulic pump and cylinder work, needs TLC, asking $500, 60 inch mower deck needs blades asking $150. I have the other headlight. I have other D-250's priced between at $250 and $750 that start and run in all gears but hydraulic pumps do not work. They are currently stored offsite. Also have a roller and variety of spare parts available. IMG_9441.MOV IMG_9442.MOV

Looking for some transmission parts for my rj58 that I just rebuilt the 3521 spline shaft and 3522 input gear

Frame off restoration. New 13 H.P. Briggs and Stratton Vangaurd.New tires,Led lights, and much more !

1993 Wheel Horse 520 – H with 580 hours . This tractor has been well cared for as pictures speak for itself. This is a turnkey machine with no leaks or issues. It has a brand new 2 inch receiver hitch that is included in the sale. $3250 Located in Southington Connecticut Can be shipped anywhere 📞 860_681_3610

This is a Model 7-1311 Sickle Bar Mower. It is in good condition and includes the owners manual, spare blades and the bladed changing tool (a $95 value). According to the Wheel Horse literature, it will fit"B", "C" and "D" series tractors. The photo shows it mounted on a WH Model 1-7245 tractor. Pick up at my location or I will ship it at Freight cost. Please call for details. Also, if youy would contact me direct65 at, ncletis@yahoo.com I would appreciate ir. Thank You