Leaderboard

So I wanted to post a topic on the 48" dozer plow, and it capabilities when paired with a hydro lift 300-500 series tractor. I had many doubts that I would actually be able to grade and spread fill and loam with my machine, but like anything else, was willing to try. I was able to spread and grade 10 yards of fill in about and hour with no real heavy abuse to the machine. Figured I would share the wealth. The community of red square helped me put this tractor back in running order.

Picked this little gem up today my very first rj58. Runs good trans feels good. Couple of questions, how do you check the trans oil? Also are the wheel horse decals oe? And is the clinton the right motor or should it be a k91 kohler?

homework time for you google "335hz 12v hella horn" find the manufacture's data for power consumption if power consumption is in watts, divide that number by 13.8 to give amps drawn when vehicle is powered up. double that amp draw (for a generous safety margin) and select a switch for the doubled amperage.

given the short wiring run in the average LG tractor, and considering the horn will likely be less than 10 amps, forget the additional wiring required for a relay. Wire the horn thru a fuse then thru an automotive quality momentary switch directly to the horn.

I like it, but I think I would move that one inside. I think thats an older sign I would want to be able know that its safe but thats just me

Got my new 55 Rj35 and my older 57 Rj35 out today for the first time this spring! They both have been sitting in different barns for many years.

Just put gas in her today and she fired right up. It's been a labor of love, when I first got her everything was shot.Thanks to everyone on the forum for all the help. Looking forward to the next round hood project.

In a previous thread, several folks asked me how I painted my rims with tires already mounted. I recently did another set, so I illustrated the process as I did it. Typically, I like to paint the rims after they are mounted anyways, because inevitably when you have tires mounted on painted rims you’ll always scratch or nick them somewhere. I like to get the rims all cleaned up, blasted and primed, then mount my tires. Here’s my process: 1) Rims were sandblasted and primed with self-etching primer. Tires and tubes were mounted. Everything was wiped down with a pre-kleeno wax and grease remover prior to taping. 2) Using blue 3M tape, I go all the way around the rim slipping the tape between the rubber and rim occasionally tucking it tight with a very small standard screwdriver. 3) Then I create a wider tape ring a few inches out from the rim lip. 4) Slide the whole thing into a kitchen garbage bag. 5) Cut a hole in the bag revealing your tape ring below. 6) Tape the bag to your tape ring previously created on the tire. 7) For silver rims, I like Eastwood Silver Argent rally wheel paint and I use a Rust-Oleum Crystal Clear. http://www.eastwood.com/silver-argent-rally-wheel-paint-set.html 8) I wipe the rims down a few more times with a pre-kleeno wax and grease remover, blow them off with the gun, then shoot two coats of color and two coats of clear. I find that the Rust-Oleum clear holds a much better shine if you don’t let it set long between coats. As soon as it flashes, hit it with round 2. I do all four coats in about 20 minutes.

belt is 1/2 w by 29 L BTW it's easier to drain the trans by removing one of the lower bolts and easy to refill through the shift lever hole after removing the shifter

Gotta agree with everybody else, John. Not what I was expecting to see knowing you can't spell! LOL

My first was a C175 auto that I got up in Oklahoma that had thrown a rod in the KT17. I gave $210 for it because it was in good shape other then the engine. Bought another KT17 in Dallas for $50 that had the same problem. Mixed the two engines together and got it running. That was a bunch of years ago and much to my surprise it is still running. No place to store inside so it and a C120 live outside and both will start anytime with no problems at all.

Ok, the show has came an went!! Where are the pictures???

my favorite thing to do is ...

My first, was certainly not my last.

A long overdue update... bendy now has decals! I finally made an exhaust , it was annoying the neighbours Cue a piece of child's swing, a table leg and lots of holes Filled with fibreglass and welded up and a nice stainless heat guard And finally.... Bendy now has a remote locking diff Used a bike brake cable in order to span the articulation joints and make life a bit easier. Spring loaded selector keeps it in or out of lock And a quick video http://youtu.be/Kw6FG_wYTqA

I really like the way the two piece cultivator works on the 1961 Wheel Horse 701 with the Hein-Werner hydraulic pump. It tool a fraction of the time to cultivator the vegetable garden from what a small tiller would do !

my first horse was a 657 (that I kinda stole from the hubbie) but the first one I bought for myself was an early 68 charger 12. after that there are alot more...love them horses!!!

Cool find!

The other guys have you covered on your questions. I just wanted to say that is one nice RJ

Dig the new RJ too.

Look see above Ed... John's already done killed that hairy bush.

Was driving down the road and saw this for sale and decided to pick it up.Any one know what years this would be?

For front tires, grab a 2 or 3 square foot section of rubber pond liner. Cut out a round hole in the center of the rubber mat. Size the hole about 60 - 70% of the rim diameter. Detach the tire from the rim bead, stretch the rubber over the rim and it will both self seal to the inside of the rim and drape over the tire and protect it from overspray. Rear tires require a larger section of pond liner. Once the paint is dry to touch, stretch the liner to remove it. The stretched liner will flake off the overspray and the liner can be reused over and over.

Put her together and run her

I don't know what sort of steering wheel your tractor uses, assuming it's an A-800, but I am planning on using a Grant style steering wheel with a Corvette horn button/switch on my 18 Auto Resto-Mod, Mark.

so, coming back from fishing this morning, saw this with some other steel piled in the front of an old house with a free sign. asked if I had to take it all and was told no, pick what you want. now the question, What do I have? I already have figuered out that it probably is not compatible with my 414-8

Hey...it was a long, hard winter boys... and bikini season has just started here.

Sorry steve, having technical issues with the I-cloud and my new laptop.....hopefully soon

This is turning into a great little show. Looking forward to seeing some of the Illinois guys and any others who are close enough to make it there.

​She helped out a little too! ​Well yeah, it was her bush you were working...right?

No it isn't the shout box. Just a post from the shout box one night that Steve thought should be kept for fun. I hope the shout box comes back too. I think Karl is working on it.

Mrs Miller sounds like someone when he wears socks! we got your phoenix

Makes for a rude awakening. Here is what happened to mine.

I PLAN TO GO ON SATURDAY WITH MY 1054 DIESEL WHEEL HORSE. RUSS

Plan to be there Saturday. Not sure if I'm displaying anything this time. The wife like this show since it has all the flea market stuff on the other side but she probably doesn't want to spend the whole day.

MY FIRST WAS A 1959 RJ MY FATHER NEW. MY FIRST I BOUGHT NEW IS A 1975 B80.

I cant believe I haven't seen this posted yet. This is the only one I can make it to, so I hope to see plenty of other Horses represented! Wednesday, May 13th through Saturday May 16th.

You forgot step # 9 .... stepping back and grinning ear to ear ......

Hmm, how old was Steve in 1964?

I'm Planning on being there with my three kids provided the weather is good .....and I hope the weather is good because this show is all I hear about every night at the supper table.....

I got into it after my Dad passed and I inherited the 4 he had...but I always considered them his. So my 1st one happened when I went to the Big Show in 2010. The raffle tractor that year was a rescued B-100. $5 got you 6 tickets and they called my name. How cool is that??

I'll be there as usual

My 1977 C-120 bought new with a 48" deck, many hours and three engines later.

my 1957 rj35 rescued from a junkyard before and after resto

In 1989 I traded a very worn out 1975 Harley Davidson Sportster for my C-175 8 Speed which I still have and use. It had a 48 inch deck, snowplow, tire chains and wheel weights. I have all of them I would bet that whoever ended up with that AMF era Harley doesn't have it anymore! Still the best trade I ever made and no one has ever forced me off the road on my tractor!

Had a very good time at the swap too, was very nice to meet you terry. Sadly, it looks like I'm going to miss in the fall as that is the same weekend as the local show for me. Look forward to the next one in the spring!

As cold as it was(BRRRRR), I found a few items that I wanted and was glad I came. Also , It was nice to meet a few new people and connect the names with the faces.

Sorry I missed tou guys too- I got there at 730am , found what I wanted, except a couple things no one had-talked to Burly a Bit and left in the middle of a rain shower. Getting too old and busted up to stand much cold, wet anymore- we'll try again!- Thanks- Al