Jump to content
RJ Hamner

416-8 Clutch linkage Problem

Recommended Posts

RJ Hamner

Its been a while since I was able to work on my 416-8 rebuilt and right now the few brain cells are having a tough time.:blink:

I am in the process of putting the wiring harness back in and the problem is the clutch safety switch.

The arm with the idler wheel that engages the switch is over ridding the switch arm.

I had tried adjusting the rod from the peddle to the arm but no matter my adjustment I still have the problem:wacko:

I am kinda at my wits end on this one.:confusion-helpsos:

Any help will be greatly appreciated

Bob

DSC_1025.JPG

DSC_1026.JPG

Share this post


Link to post
Share on other sites
 
gwest_ca

Idler pulley shaft pin.jpg

Share this post


Link to post
Share on other sites
 
RJ Hamner

Don’t think so. It slides in from the right and the bracket for the rod from the peddle fits on the end. The nuts and spacers for the idler and the Minnie shock absorber would be in the way

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • John A
      By John A
      The clutch spring  on my 308-8 broke, so the tractor stopped dead.   It was easy to see the broken red spring,  after I removed the right rear wheel.   I  was able to order a replacement spring which I replaced today.  Problem now there is too much slack on the drive belt.  The tractor will move, but barely as if the drive belt is not tight and slipping.  It seems that the clutch pulley isn't applying enough force against the belt.  I have  tried adjusting the clutch rod but that doesn't seem to make a difference.  It only changes the position of the clutch pedal .  I don't see any other adjustment option to put more pressure on the drive belt.  The belt is old, but seems acceptable.  Before the clutch spring, broke, the tractor would jump out in any gear.  No slippage. 
    • Aeladon
      By Aeladon
      I actually work at a lawn and garden dealership. A friend of mine is trying to restore his GT-14 and he needs a clutch. Toro's IPL are incomplete but I managed to find the pdf for the parts list elsewhere. I came up with a number of 9656 for the electric clutch which subbed to a 101473; both of which are discontinued. So here is my question... Does someone out there have the manufacturers number for that clutch. I have access to about 30 different manufacturers so i could probably find a clutch that would work but most of them don't publish shaft sizes in an intelligible format. With the manufacturer's number I could probably easily substitute it.
       
      Any help is greatly appreciated - this sight has helped me in the past, personally and professionally so I know if anybody can help it will be you guys. 
       
      Thanks,
      Ael
    • Tim.0
      By Tim.0
      I seem to be missing the clutch shaft, the bearing is bad and the piece to the left. Does the piece to the left go with this assembly? Looks like there is  a ring around it for a snap ring. the piece is a 14-54 bearing race and if I put it in the pulley assembly then I can not put the pulley assembly on the PTO shaft. Maybe it is to reduce for a smaller shaft?
      The bearing inside must be a press fit? I have not had time yet to remove the snap ring. This would be the bearing by the snap ring you can see, the needle bearings look okay.
       I suppose I could try and get a bearing from the bearing store but then I still need the clutch shaft to match up the size Looks like the clutch shaft goes inside the bearing and there is a snap ring to hold it in place from a diagram IC.
       
      Would the pulley from a commander 800 be the same, I c one for sale. Has the manual clutch shaft on it.
       
      Thanks  Tim O


    • Joebag
      By Joebag
      okay guys what am I missing here on the left left side control peddle arm that you work with your left foot to stop and go. The pedal just stays down and no way of stopping by just lifting your foot so the peddle can raise up and down

    • snrohio2288
      By snrohio2288
      Hi Guys, new here. About a year ago I bought a house which came with a nice 208-4. The tractor was abandoned by the owners of the house in the shed as it "wouldn't start anymore".
      Turns out mice had made a nest in the engine shroud and chewed through the spark plug wire. A new coil and battery later and she has been serving me well for a year.
       
      The other day though, after stepping on the clutch and letting go, the tractor didn't move anymore. Came to find out my clutch spring had broke (found part of it in the yard).
      I ordered a new OEM spring and it arrived. The problem I am having is I can't seem to find where the other end of the spring attaches to the frame.
      I have a diagram I found online but it simply says "hole in frame opening".
       
      Does anyone know or have a similar model they can look at and guide me where this spring goes?
      See attached diagram.
       
      Thanks
       
       

×
×
  • Create New...