Stepney 2,314 #1 Posted September 17, 2019 Hello, all. Looking at possibly trading a pair of old 42RD decks with a fellow for a 48" SD. Been trying to find a good one for a while, and this one is in really good shape. It's a 1973 model, and I can see from the photos is has the sealed spindles. Would I be correct in assuming this is a Double D pulley and blade type deck? I seem to recall having a bit of a hard time getting DD type blades for my last tractor. Is it possible to use newer 48" deck aluminum spindles on this unit? I've never actually had an older deck working, most of mine are 80s era. Share this post Link to post Share on other sites
gwest_ca-(File Mod) 10,478 #2 Posted September 17, 2019 Some info here Mower DNA 48" side discharge 1966-1967 model RL-486 replaced by 1968 model 5-1481 1969 model 5-1482 1970 model 5-1483 1971 model 5-1200 1972 model 5-1201 1973 model 5-1202 1973-1974 model 5-1210 1975 model 5-1211 1976 model 65-48MS01 1976 model 65-48MS02 1977 model 75-48MS01 - These all used blades with 5/8" x 3/4" double-D center hole unless the spindles have been upgraded. ------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Note - 3/4" or .750" is 19.05mm 1977 model 75-48MS02 - Uses 6203 bearings with 3/4" ID - (First deck to use blades with 3/4" center hole) 1978 model 85-48MS01 - Uses 6203 bearings with 3/4" ID 1979 model 95-48MS00 - Uses 6203 bearings with 3/4" ID 1979 model 95-48MS01 - Uses 6203 bearings with 3/4" ID 1980 model 05-48MS01 - Uses 6203 bearings with 3/4" ID 1981-1983 model 05-48MS02 - Uses 6203 bearings with 3/4" ID 1984 model 05-48MS03 - Uses 6203 bearings with 3/4" ID Note - 17mm is .669" 1985 model 05-48MS04 - Uses 6203 bearings with 17mm ID 1986-1988 model 05-48MS05 - Uses 6203 bearings with 17mm ID 1987-1988 model 05-48SC01 - Uses 6203 bearings with 17mm ID 1989 model 15-48SC01 - Uses 6203 bearings with 17mm ID 1990 model 15-48SC02 - Uses 6203 bearings with 17mm ID 1991-1992 model 15-48SC03 - Uses 6203 bearings with 17mm ID 1993-1997 model 78360 - Uses 6203 bearings with 17mm ID 1998-2007 and 2009-12 model 78361 - Uses 6203 bearings with 17mm ID - These all use blades with 3/4" center hole Garry Share this post Link to post Share on other sites
gwest_ca-(File Mod) 10,478 #3 Posted September 17, 2019 This will help if you know the model number of the deck Garry Share this post Link to post Share on other sites
Lee1977 6,210 #4 Posted September 18, 2019 (edited) The newer spindles will mount up in the same holes. The deck shell is almost the same it's full depth in the front where the later models have an inch or so trimmed off the front bottom. I have a 75 series 48"deck that new had DD spindles. over the years I had 3/4 keyed , now it had metric. If you have the newer spindles from a 42" deck they will fit but the pulleys are different . They are larger on a 48" deck. Edited September 18, 2019 by Lee1977 Share this post Link to post Share on other sites
