Jump to content
RJ Hamner

1970 Charger 12 Limited travel with the hydro lever

Recommended Posts

RJ Hamner

It acts like the lever has limited travel and doesn't go far enough to go into reverse.  Something binding?  Bent?

The tractor showed signs that it had a rollover sometime in its life. Right front axle was welded along with some of the steering parts. 

I have a 68 charger (for parts) and swapped out the repaired parts with it.

Possibily bent something there or the friction assy?????

Share this post


Link to post
Share on other sites
 
pfrederi

Is it a new issue? Have you tried the neutral adjustment? Check the plate at the rear of the frame the hydro bolts to, Could be cracked causing alignment issues

  • Like 2

Share this post


Link to post
Share on other sites
 
RJ Hamner

Well, I solved my problem.:)

I had gone back out to the shop and looked at the 68 part and noticed that it had full travel

Went back to the 70, said a few things that I can't relay on this forum:bitch: and just gave it a good yank.:violence-blades:

What ever was binding or"stuck" loosened up.

I used this same method to get the steering wheel of my C121! :D Go Figure

Thanks for the quick reply

Bob

  • Like 1
  • Thanks 1
  • Haha 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Hardy6
      By Hardy6
      Hi I recently got an old charger 12 that had been sitting in a friends backyard for at least 20 years. The engine spins over and the starter works but it has no spark, I’ve been looking online for some solutions but I can’t seem to find any other charger 12s with my ignition setup. It seems to have a sort CDI box but I’m not sure. Does anybody know how this works or any tips on how to test for where the problem is ? 
    • BrianKoch
      By BrianKoch
      Hello gentleman, 
       
      Problem: will not crank on its own, will crank with jump box—but still not fire
       
      Recent things I did prior to this issue: cleaned fuel filter, replaced battery cables, replaced cable from ignition to starter
       
      I have my test light out and am probing around. 
       
      There is no power at ignition/magneto wire or the ignition/starter wire
       
      There is power everywhere else






    • TonyI
      By TonyI
      I have a 418-c  worked great plowing over the winter.. but now is having no power pulling a load fwd.
      replaced the fluid.. the old fluid didn't look bad. feels a littls better., but still significant loss of power and high pitched whine coming out of the hydro.  the lift works fine
       
      is there a repair manual our there for the hydro?  Is there a way to reverse flush the system?   I hear sometimes the hoses crack internally and clog things up.
    • mattd860
      By mattd860
      I have developed a kit that allows a Wheel Horse / Toro hydrostatic tractor to be operated by a pedal on the right side of the tractor. The original forward/reverse lever can be retained or removed. The kit includes everything needed to install the pedal kit and installation is simple with the help of a downloadable installation manual. Additionally, only one (1) 1/4" hole will need to be drilled which can be done by a hand drill. No other drilling or cutting will be necessary. Any tractor with this kit can be converted back to stock without any visible evidence that kit was installed. However, you'll never want to do that

      The kit operates very simply and similar to modern tractors. When the pedal is pushed forwards the tractor will move forwards. When the reverse pedal is pressed downwards, the tractor will moved in reverse. If the operator takes his foot of the pedal at any time, the pedal will automatically center itself and the hydrostatic transmission will return to neutral (stop). This enables the operator to use both hands on the steering wheel or one hand on the wheel and the other operating an attachment like a snow blower, plow, etc.

      The foot pedal is custom cast in Aluminum, uses brass bushings to minimize wear, and it closely matches the OEM Wheel Horse BRAKE pedal commonly found on 8-speed manual transmission tractors. Modifications were done to the pedal to add the reverse pedal and adapt the pedal to the rest of the kit. For the most part, the pedal looks like it was designed and manufactured by Wheel Horse / Toro. Additionally, a grease fitting has been adapted to the pedal to further minimize wear and tear and if the brass bushings ever wear out they are fully replaceable without having to buy a whole new pedal. 

      The pedal kit fits the following series tractors with Eaton hydrostatic transmissions: C-1X5, 300, 400, 500. 
       
      My kit can be adapted to older hydrostatic tractors with the Sundstrand transmission, however, you will need to find an updated hydro cam commonly found on ebay. Message me for more information. 
       
      Here is a link where you can download the installation manual: CLICK HERE
       
      I am selling these kits for $330 shipped to anywhere in the United States. I offer multi order discounts as well. I will also sell to other countries for additional shipping charges to be determined.
       
      If anyone has any questions please feel free to PM me or post your question here and I will be glad to help. Or you can email me at mattdarling02@hotmail.com.

      Thanks!
       
       
      Below are pictures of the complete kit and the pedal installed on the tractor. Some modifications have been made since these pictures were taken. For example, the reverse pedal is now cast in aluminum instead of the steel pedal shown below. 
       

       

       

       

       

       
    • bigcreek
      By bigcreek
      Price DROP!!! Horse traders out there, this great tractor is available at new price. 
      99.5 hours, Horse runs like new. Really Like this horse to go to good home. Let’s talk can provide more images if needed 
       
       




×
×
  • Create New...