Jump to content
dmhill

B82

Recommended Posts

dmhill

Does anyone know what drive belt and deck belt I need for the 1980 B 82? Also if anybody had pics of the drive belt installed I would appreciate it.....

When I picked it up both belts were/are missing. Not entirely sure all the necessary hardware is under there either, however, it seems complete. Thank you in advance.

0317181156.jpg

  • Like 1

Share this post


Link to post
Share on other sites
 
gwest_ca

Tractor drive belt has been added to these pages. Click on the pictures.

32" width of cut side discharge?

Garry

  • Like 2

Share this post


Link to post
Share on other sites
 
dmhill

I appreciate the downloads and have looked them over. The belt I found was the one which goes from engine to the transmission (106518). This one is already on the tractor. I am missing the one which goes from bottom of engine pulpy to the top pulley on the deck and the belt which drives the blades on the deck. I do not find either of these listed here...confused!

Share this post


Link to post
Share on other sites
 
dmhill

Three belts for such a little horse!

Share this post


Link to post
Share on other sites
 
gwest_ca

The one's you can't find have been added to the mower deck page. Click on the picture to see that page.

Drive belt 108196 (1/2" x 50.3")
Spindle belt 8430 (1/2" x 59")

 

Garry

Share this post


Link to post
Share on other sites
 
dmhill

Thank you I found what you were referring to. I think I have discovered the basis of my confusion.

The deck on this machine is a rear discharge 36" three blade, well sort of...if I could get your expert option about why this deck has a side shoot as well as a rear discharge and what can be done to eliminate the side shoot I would appreciate it. I'm not sure what or how the previous owner did or didn't do. When I look up the model number it shows the deck on the Toro site. Now more confused than ever, except I believe I found the correct belt sizes for this set up.

0402180826.jpg

0402180914.jpg

0402180828.jpg

0402180827.jpg

0402180826a.jpg

0402180927.jpg

Share this post


Link to post
Share on other sites
 
dmhill

I think I finally got it! Geee...I can be slow. This is a 1981 side discharge deck where Wheel Horse essentially took a rear discharge deck and modified it to be a side discharge by closing up the rear underneath, cutting a hole in the side, and putting a "chute" on it. The pics on PartsTree only show the rear discharge deck. I will order the two (out of the three belts necessary to make it function) and new WH/Toro wheels for the deck. All my other horses are horizontal shafts so this is my first adventure with a vertical shaft machine. It just so happens I picked up a B-81 with a rear discharge deck a few months ago out of a field which has a rear discharge deck that I think I will switch all these parts over to and then put it on this machine. I knew there was some purpose in picking up that old B-81 even though the engine was mostly dissembled and all tires were flat. Must be destiny! lol

Share this post


Link to post
Share on other sites
 
gwest_ca

Looking at the ID tag with the 807x Julian build date would think it is a 1978 model with a 85-36XS01 model number. I can't read the first digit of the model number.

Julian dates start with the year (8=1978) 07x = the 70-79th day of the year.

 

Garry

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Mattgray
      By Mattgray
      I am looking for a snow plow in the Western NC area, might be a long shot but iv checked marketplace and craigslist. No luck. if anyone has one or knows where I could get one. I believe I need a long frame one for my tractor. Thank you!! sorry if I posted this in the wrong spot. One year after owning my wheel horse and still running strong! 
    • TailGate18
      By TailGate18
      Need help please 
      Can't exactly identify my wheelhorse. I believe I've pinned it between 74-79 but not sure exactly. I'm not real knowledged in mowers but interested in learning. It ran few years ago. Then parked in a storage unit for about 3 years with gas left in it. I can't get it to run at all unless using ether.
      I've drained all the old gas, I've replaced the fuel lines, new plug, new gas, but it just won't start up and keep going. I figured on new carb but don't know exactly what I'm looking for and thought I'd better know the exact details of the mower so I know I get the right parts. Any help would be appreciated. The info I do have is as follows.
      The mower itself all I could find was one tag on the frame under the gas tank.
      ID # 61-08K801-05782
      Then under that 4 digits
      6337
       
      Has a Kohler motor info as follows
      Model-K181
      Spec- 30538
      Displ (cc)- 305
      Serial #- 2613800539
       
      It'll crank but not start. Not even attempt to start. With the fuel line off of the fuel pump it shows it pumps fuel. I thought the possibility of the float being stuck in the bowl but again not very knowledged in this field. Would appreciate any insight, details, knowledge, help or anything of the sort. Or info on the information of the tractor so I know exactly what I'm asking questions about
      Says it's a B-80 8 speed
       
      Thanks in advance







    • nickjet67
      By nickjet67
      Hello all, I recently acquired a "new" B-115, and with the help of @ohiofarmer, I will be fixing her up, first with a engine he is trading me for my old Kohler engine off my '77 B-80 that I trashed when I was 13. I haven't been in the Wheel horse game long, as I am 16 now, I hopefully will be able to keep this project updated on here, especially in the spring when I will be completely repainting it! I am super excited for this project, and am ready for all the challenges that lay ahead with it. if you have any helpful information you are willing to share about my newly acquired project, please share! I haven't had tons of luck finding tons of information about it.










    • nickjet67
      By nickjet67
      Hi, been a while since I been on the forum, but I needed to log on to get some help with my "new" b-115 I picked up for $25! I saw this beauty sitting on the side of the road and I just needed to have it. only issue is it doesn't have a engine and the steering was all discombobulated. Last night I got that all welded up and now I am looking for help, I need to get the Briggs motor that came on it now, I have had 0 luck with finding the right motor for it but I have found almost every part I would need to build one from scratch. They are all over ebay and craigslist (the parts) and would be expensive but nice. Any help would be greatly appreciated! (also am looking for a snow blower and a bagger for it, dont know if the bagger for it exists but would be nice to have.
    • ken woolford
      By ken woolford
      Advice please. Aquired a B-115 cheaply, bit of a basket case with four flats, but more importantly cannot select neutral. Gear lever moves freely throught range, and on jacking machine up appears all gears work, wheels turn, but cannot select neutral which makes it very difficult to push. Suggestions?
×
×
  • Create New...