Jump to content
Giff Kucsma

Balancing mower blades w/o round center hole

Recommended Posts

Giff Kucsma

I just replaced the spindle bearings in my RM-367 mower deck.  I have a new set of OEM mower blades, but I'm wondering if anyone has found a good way to balance these blades that do not have a round center hole in them.

 

 

Mower Blade Set.jpg

Share this post


Link to post
Share on other sites
 
Ed Kennell

:text-welcomeconfetti: to the :rs:  Giff.         Clamp a knife edge in a vise and lay the blade center on the edge.      Be careful....don't get cut.

  • Like 3

Share this post


Link to post
Share on other sites
 
WHX??

:WRS: Giff, Ed' suggestion works well.

Another piece of advice.... DO NOT THROW THAT BLADE BOX OUT! That is :wicked: cool! :)

  • Like 2

Share this post


Link to post
Share on other sites
 
gwest_ca

Was never happy with the balance using the "hang the blade on a nail" method. Tried all the available balancers except the $200+ models for obvious reasons.

 

Came up with an economical solution and didn't realize until finished why it is an improvement. If you have a 2" wide blade with a 3/4" hole hanging on a nail approximately 31% of the blade weight is above the nail and 69% of the blade weight is below the nail. That 69% below the nail pivot point masks a good portion of the out of balance condition.

Pilot bearings used on woodworking router bits come in sizes matching the blade center holes of most blades and use a very light lubrication making them ideal for a balancer. Just mount the bearing on a horizontal machine screw fixed to the wall and hang the blade on the bearing. Grind until the blade stays where you put it. One thing I learned is it should be done indoors because an unnoticed slight breeze will windmill the blade it pivots that easy.

The solution is to get the center of the blade on the pivot point.

 

The 5/8" x 3/4" double-D center hole stumped me for a while. Ended up making a bushing from 3/4" round aluminum solid bar with a 3/8" hole drilled in the center. Filed 2 equal flats until it fit snugly in the hole and hung it on a 3/8" OD bearing. Problem solved.

 

Some observations.

When previously sharpened and balanced blades come off the deck dull and loaded with gunge they are still balanced if they have not hit something.

 

Have never come across a new blade that was not balanced as they should be but always wondered. Have a new 3" x 30" 9 lb. brush blade used on the Gravely 30" mowers and it came balanced.

 

Unbalanced blades are what cause decks to crack around the spindle housings. Many years ago I drilled the ends of cracks around all three spindles of a gentleman's deck and then bronzed the cracks where the metal was not missing. Should have been scrapped or at least welded with steel. He brings me the deck for sharpening and balance twice a year and as of two weeks ago the bronze has not cracked. Amazing.

 

Made a balance stand with a 3/8" x 7" x 7" plate base. Three adjustable legs for leveling. In the center is a 3/4" square tube/post about 10" long that has the different sized bearings attached to the top sides of it. My thought was the bearings need to be perfectly vertical for accuracy but that is not necessary. As long as the bearing is reasonably vertical it works. The three legs make the stand very stable.

 

Garry

  • Like 3

Share this post


Link to post
Share on other sites
 
Jerry77
1 hour ago, gwest_ca said:

I drilled the ends of cracks

Good job ! it is the only way to stop a crack from spreading....:)

Share this post


Link to post
Share on other sites
 
Giff Kucsma
On 4/25/2017 at 6:02 PM, Ed Kennell said:

:text-welcomeconfetti: to the :rs:  Giff.         Clamp a knife edge in a vise and lay the blade center on the edge.      Be careful....don't get cut.

 

Thanks, Ed.  I don't know why I tend to over-think problems like this.  I didn't have a knife handy but did have an old wide blade chisel that worked as well.

 

Blade Balance.jpg

  • Like 1

Share this post


Link to post
Share on other sites
 
WVHillbilly520H

My dad has had/used one of these aluminum balancers for as long as I can remember and I have used the plastic version with success but have finally got myself an aluminum one, 18 years on my 520 deck and no stress cracks or dad's CC ORIGINAL he's owned since '76-'77, well worth the $7, Jeff.

Screenshot_20170428-215354.png

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • MSBiker
      By MSBiker
      Well it looks like I'm out of luck. I have been looking for blades for my Lawn Ranger and having zero luck. I have tried Wheel Horse part numbers 7908, 7909. Toro part numbers 8777, and 53322 and no one has anything like this. I was thinking about doing a cut down, but finding right hand and left hand blades seems to be the problem. 
      Anyone making blades, constructing blades, got a work around, etc? My blades are usable, but that is about it. 
    • Joe Warren
      By Joe Warren
      New Old Stock Toro/Wheel Horse Blade Kit #108004
      This kit contains two # 108171 blades
       
      Diagonal length:               18 3/4”
      Blade width:                       2"
      Center hole:                       13/16” x 1” double D slot
       
      Used On:             37” Side Discharge Mower   (1981 - 1983)   Models 05-37MS01, A5-37MS01
       
      $39 includes shipping within US lower 48
       
      One blade set available. Limited number of other NOS mower parts available (blades, belts, spindle components). Please private message me if you are interested in purchasing.
       
      Thank you
      joeww121@gmail.com

    • Joe Warren
      By Joe Warren
      New Old Stock Toro/Wheel Horse Blade Kit #106637
      This kit contains three # 106078 blades
       
      Diagonal length:               16”
      Blade width:                       2"
      Center hole:                       3/4” diameter
       
      Used On:             48” Side Discharge Mower, VIN/Models: 05-48MS01, 05-48MS02, 05-48MS03, AS/05-48MS02, 05-48MS04, 05-48MS05, 05-48XS01, 05-48XS02, 05-48SY01, 05-48SY02, 05-48SC01, 05-48SC01, 05-48SS01, 15-48SC02, 15-48SC03, 75-48MS02, 75-48XS02, 85-48MS01, 85-48XS01, 95-48MS00, 95-48MS01, 95-48XS00, 95-48XS01, 74352, 74353, 78260,  78261, 78290, 78360, 78361, 78363,
       
      $49 per kit which includes shipping within US lower 48
       
      Two 106637 blade kits available. Limited number of other NOS mower parts available (blades, belts, spindle components). Please private message me if you interested in purchasing.
       
      Thank you
      Joeww121@gmail.com

    • TN Dave
      By TN Dave
      Hi all:  The people on this forum have been helpful in the recent past, so I'm hoping that those of you who are more mechanically-inclined than I am (...which is 100% of you, I'm sure...) might be able to point me in the right direction again.
       
      My apologies is this is too basic, but I have an old 310-8.  It has 3 mower blades, and I can't get any of them off to sharpen them.  
       
      If I use a floor jack and a couple of jack stands, I can lay down on the garage floor but can barely get a 3/8 inch electric drill with a sharpening stone attachment properly angled against the blades.  I've also put the front wheels up on plastic ramps (Rhino Ramps) which I use for changing the oil on my car, with pretty much the same result.  
       
      These work OK for touching up the blades just a bit, but the blades really need a good sharpening, so I am trying to get them off in order to use a bench grinder.
       
      I have sprayed a pretty fair amount of penetrating oil on the bolt heads above and below the point where they go thru the blades.  I have used the longest pipe wrench I have (18 inch). Frankly, I'm a bit concerned that the amount of leverage I'm using might pull the mower off its jack stands.  
       
      In any event, the blades are still very firmly attached.
       
      Any suggestions on how to get the blades off will be greatly appreciated.
       
      Many thanks in advance.
    • porschpow
      By porschpow
      I have been noticing that the mower leaves behind streaks of uncut grass while mowing.  It looks to me as if the blades need replacing/ sharpening.
       
      Does anybody still sharpen their blades or is it not cost effective enough.  If they do, how do you go about sharpening it?
×
×
  • Create New...