Jump to content
Danny856

Looking for a belt....

Recommended Posts

Danny856

Hey guys, I'm sure the answer is somewhere on this site but for the life of me I can't find it. I have an '89 Wheel Horse 310-8 (210K806) and my mowing deck is 0542MR04. I need the belt that connects the two. The one that goes from the engine/mule drive (?) down to the deck. It kept poppin off. I thought I finally had it set right but then it came off again and I ran over it. Can anyone help? Thanks in advance. Dan. 

Share this post


Link to post
Share on other sites
 
rmaynard

Dan,

 

Here is the info you need:

 

Drive belt 108834 (1/2" x 98") [Replaces 102741 as per PSB #272 in this application]
Spindle belt 106125 (1/2" x 89.03")

 

 

 

 

 

and :WRS:

Edited by rmaynard
  • Like 3

Share this post


Link to post
Share on other sites
 
Achto

:WRS:  Looks like rmaynard  has you covered.

  • Like 1

Share this post


Link to post
Share on other sites
 
Tankman

:WRS: Maynard has your belt info. Right on!

TSC (Tractor Supply) has Huskee Kevlar belts on the rack, inexpensive. Never had one fail.

Magic Marker the sleeve, "310-8 42" RD deck, drive". Staple the belt sleeve to the shop wall.

 

Girls don't pump gas in New Joisey.

Edited by Tankman
  • Like 1

Share this post


Link to post
Share on other sites
 
Danny856

Thanks guys! I knew I came to the right place :)

  • Like 2

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • 87 312-8
      By 87 312-8
      looking for mule drive bearings for a 36 inch rear discharge deck 1986/87 312-8, thank you
    • OHLB
      By OHLB
      Newbie here. 310-8 won't start. Battery is dated 10/19. Did crank a couple times but started losing ummph. Should I replace it or attempt to charge it? Can't tell if the battery is frozen. Never knew until today that batteries could freeze and that it's dangerous to charge a frozen battery. It's been single digits with wind chill the last couple weeks here. 
    • Big Rig
      By Big Rig
      ISO clutch neutral safety switch for 310-8
      or alternative 
    • Rob R
      By Rob R
      Soo couple of years back did a pulley change on the tranny from 6 inch to 4.5 and used a 1/2 X 79 belt to make it work and it worked fairly well but wanted to get back to a 5/8 drive belt so went to a 5/8 x 81 inch belt and added a second flat Idler pulley. I simply cannot believe how smooth and sharp it shifts and drives now!  The added flat Idler was 2 3/4" with a 5/8ths bore used and existing hole on the side shroud and just opened it up a bit. I use to slip a bit on steep hill with the 79" slips no more, the belt drives and the clutch is  LOT smoother and in the right pedal area.... Will see how it holds up cut 3/4 of an acre of grass yesterday NO issues. 





    • Ifixoldjunk
      By Ifixoldjunk
      So I was out mowing the other day with my 310-8 and somehow snagged my wheel in a hole in the yard. Anyways I pretty much destroyed my ball joints. I've since replaced the tie rod with junkyard parts but I was wondering if anyone's found a heavy duty aftermarket replacement for the tie rod assembly.
       
      Like would generic adjustable go-kart tie rods do the trick?
×
×
  • Create New...