Jump to content

moe1965

Supporter
  • Content Count

    199
  • Joined

  • Last visited

Community Reputation

185 Excellent

1 Follower

About moe1965

Wheel Horse Information

  • favoritemodel
    Raider 10

Profile Information

  • Location
    Elyria ohio
  • Occupation
    Water department
  • Interests
    metal detecting making steam and air whistles

Recent Profile Visitors

2,044 profile views
  1. I will be a first time user as well this year. If we get snow. Can't help with your question but I will be tuning in just in case I have the same issues
  2. moe1965

    Kohler engine

    Hello all. I rescued this from the scrap pile and have no idea what horse power it is. There are no tags. On it any where I'm guessing it was on a cub or a gravely due to the color. I guess my question is does it have any value to any one other then a boat anchor. This thing is HHHHEAVVVVY i have no use for it. It is not locked up. I also scored a complete Clinton engine. I would be happy to give it to someone if they wanted it you just have to come pick it up
  3. moe1965

    Chains vs Brains

    I would think you could just add a link or two and be ok
  4. moe1965

    Plow On

    That's on my list this weekend I'm a little further north of you in Ohio 30 miles west of Cleveland just finished mulching leaves with my zero turn.
  5. moe1965

    Home made hitch for C160

    Very nice work
  6. What is this drill used for. There is a piece that screws out of the handle that is used to advance the drill bit. It ratchets like a ratchet wrench and there are three detente to choose from that you can see in the picture to select from to position the drill. There is a point on the opposite end of the drill that I'm guessing is used so you can push it up against something so the drill will cut. That is what the piece that screws out of the handle is for. I'm guessing it is used to drill holes in ceiling joists.
  7. moe1965

    Fuel pump on d160

    Sorry Trevor this will probably not be much help but I included pix just in case mounting could be of some help. Probably not because of different engine types.
  8. moe1965

    Fuel pump on d160

    Red wire is positive psi might be border line to much mine is below 4 psi. I'll send pix tomorrow evening for where I mounted it the tractor it is at my dad's house. You will have to make a plate to cover the existing pump mounting if you are getting rid of the existing mechanical pump
  9. moe1965

    Seafoam. Your thoughts

    Well here is the results. I used marvel mystery oil instead. I burned through about 4 gal of gas in the c141 mowing and riding around etc and I just backed it into the garage idled it down and backed her in at a very low idle and it didn't even think about sputtering or stalling. Let it run for about 5 min at a low idle and no issues. I hope it saved my problems. Still not not sold on the whole ring in a can thing and voodoo etc but I'm good for now. Thanks for all your input and experiences jk
  10. moe1965

    Seafoam. Your thoughts

    Thanks for all your comments. Not sure what I'm going to do yet I'll will keep you all informed.
  11. Had this happen to me.
  12. moe1965

    Seafoam. Your thoughts

    I have a c141 which runs real good but the low idle is a little rough. I have adjusted the low idle screw and it has little or no change while adjusting it. I'm sure it has a little dirt or some causing my issue and thought I would try seafoam to correct my issue so I wouldn't have to take the carb off and clean it. The tractor sat for about 3 years before I acquired it and I have ran about 3 tanks of fuel through it hoping it would clear it self out. Any one ever used seafoam? If so what are your thoughts. Im a little skepical on things in a can claming to cure all etc. lThanks
  13. moe1965

    How do you fix a gas tank? And my new purchase...

    Not sure on plastic tank repairs but red kote fixed a aluminum one I had. You pore it in the tank and slosh it around worked great. You could call the manufacture and ask them if it works in plastic.
  14. moe1965

    Plow scraper blade replaced

    The mounting holes that held the cutting edge I had to replace with a small piece I welded to the blade. I will be drilling holes to attach the cutting edge. I'm using a piece that is 3/8 thick it should last me my life time I hope
  15. moe1965

    Plow scraper blade replaced

    Mine measured 11 in. Center to center
×