Jump to content

boomers_influence

Members
  • Content Count

    183
  • Joined

  • Last visited

Community Reputation

102 Excellent

4 Followers

About boomers_influence

  • Rank
    Advanced Member

Wheel Horse Information

  • favoritemodel
    520H

Profile Information

  • Location
    hastings mn 55033

Recent Profile Visitors

3,674 profile views
  1. boomers_influence

    My 520 doesn't charge while mowing and then dies.

    club the original P coil ( 166-0761 ) is held in by 2 bolts that are 180 degrees apart it' s specs are 2.9 -3.6 ohms on the primary, 14,500 to 19,800 ohms on the secondary. the replacement onan coil ( 166-0820 ) needs a special bracket to mount it. the primary is the same at 2.9 to 3.6 ohms. the secondary is HIGHER, 20.600 to 21.000 ohms. thank you. boomer
  2. boomers_influence

    Onan Breather / Decal

    bo i may be able to send you a good pic. thank you. boomer
  3. boomers_influence

    Onan Fuel Pump Recommendations

    mjh FYI the onans from about 1988 on used the nikki fuel pumps. ( made in japan, a VERY GOOD pump ) thank you. boomer ( the used onan engine parts guy, also NOS and new )
  4. boomers_influence

    Any guesses what this engine is?

    kohler, also. thank you. boomer
  5. boomers_influence

    1979 Onan B43M 16hp

    club FALSE information given in the above post the H8 was used in the CCK family of engines. the CORRECT plug for the B 43-48M is RH 18 Y thank you. boomer
  6. boomers_influence

    Onan 16 hp surging at low idle

    chas you saying you have a 1997 engine tells me you have the piece of crap emissions carb. ( 146-0697 ) they DO NOT want you to rebuild /clean them. there is no manual that shows the parts orientation / location. thank you. boomer ( the used onan engine parts guy, also NOS and new )
  7. boomers_influence

    520H running away

    arthur you DO NOT have the throttle arm correctly installed installed on the carb end. also the spring in the governor arm goes to the SMALL hole. please e/mail me and i will send a pic of the correct install. boomers_influence@yahoo.com thank you. boomer ( the used onan engine parts guy, also nOS and new )
  8. do you have carb kits for the 520s. I have a buddy that has a 96 520 that gallops when it runs. he does not want to take the carb apart if he can't find a carb kit. he needs other parts to. could i get your phone number. He has no computer. Thanks Dave

    1. boomers_influence

      boomers_influence

      dave

      boomers_influence@yahoo.com

      651 437 2826 M-F 10-7  S-S 12-6 cent time.

      please give the 146-0xxx # from the side of the carb,

      above the throttle shaft arm.

       

      I HOPE it is not 146-0698 ( emissions carb )

       

      thank you. boomer

  9. boomers_influence

    518 Running odd

    muz make and model of engine, please. thank you. boomer
  10. boomers_influence

    P220G - Removing Crankshaft

    TC you NEED to use socket head cap screws. ( they are grade 8 ) thank you. boomer
  11. boomers_influence

    520H Not Getting Fuel

    tc try a divorced fuel tank located on the top of a 5 foot stepladder, with the fuel line from the tank hooked directly to the inlet of the carb. thank you. boomer ( the used onan engine parts guy, also NOS and new )
  12. boomers_influence

    6100 carb 20hp Onan

    bo you have the emissions carb. ( 146-0698 ) the 146-0326 gskt IS NOT FOR your carb. ( it is for the 300 series of carbs ) you need to purchase the 146-0657 kit to get that gskt. i do have a new gskt for that carb. 651 437 2826 M-F 10-7 S-S 12-6 cent time. boomers_influence@yahoo.com thank you. boomer ( the used onan engine parts guy, also NOS and new )
  13. boomers_influence

    Weird surging problems with 520H

    club i also had a P 220 main jet the was partially blocked. you MUST remove them to clean them. if you use a tip cleaner, without removing the jet you will just push the debris into the body of the carb. thank you. boomer ( the used onan engine parts guy, also NOS and new )
  14. boomers_influence

    Oil filter on the 520

    bo the 122-0800 is mainly for the Big Block engine 4.2" long. ( P 224, T-260 N series etc. ) the small block is usually the 122-0645, 3.5" long. thank you. boomer ( the used onan engine parts guy, also NOS and new )
  15. boomers_influence

    Carburater help

    matt the 146-0479 was first used on the P 220. ( same CID as the B 48M ) it has a # 238 venturi and a # 134 main jet if the P.O. wanted to use a Nikki carb for the B 43M he should have used the 146-0412 or the 146-0478. ( both have a # 205 venturi and a # 120 main jet ) boomers_influence@yahoo.com 651 437 2826 M-F 10-7 S-S 12-6 cent time. thank you. boomer ( the used onan engine parts guy, also NOS and new )
×