Leaderboard

My local Battery Warehouse will make cables for me, any gauge, and length, any lug size. Usually around $5.00 each or less.

Rule # 1 Hillbilly is never wrong. Rule # 2 When Hillbilly is wrong see rule # 1

Hello everyone this is Brennan Bo, Steve Bo's son since I am 11 years old I told my dad that I wanted my own account so here I am.

I have my reasons, cause I'm allowed to.. Will be 71 years "young" next month so.....I do whatever I like. This evening however I totally lost it. I think? Went into the corral with my doggie, and waxed (Turtle Wax) my '90 520-8 while the doggie sniffed around. This Stallion works hard! Deserves a rub down. Now I'm thinking, "Tire paint. Why not?" I have a gallon (haven't used any in a year or so ). Think I've gone too far, too far gone? Guess it's WHA (Wheel Horse Addiction). Could be worse. I guess? Goodnight Deere ().

Hello all, Took my Mossberg 500 out and a box of slugs. Its that time of year and I added a scope to mine. Started smashing 1 ounce slugs at 1400 fps into 2 propane tanks I have out back. Man it caves in the side at a minimum and punches clear thru 50% of time. I hit both tanks and they go sailing and crash to ground. I pick em up to reset and this little guy is looking out all big eyed going WTF was that! Lmao... session over, Ill leave you alone (unless you move into one of my Kohlers!) Tony

Benny survived blast off.

Have been making my own for a few years now. I buy good quality mig ground cable from princess auto, the stuff with high silicone content in the jacket. Then clean the inside of the lug with a little wire brush and flux it. Strip the cable end so about 1/16 will stick out and flux the cable too. Set up in the vise with a 5/32 drill shank and the lug and squish it down with the wire in it. Heat and solder fill till it comes to the top. Then clean with alcohol and heat shrink. I've done them without solder and never had one come loose even though it's not a true toothed crimp. Works for me

Got the call to see if I was interested in a few signs. Couldn't get there quick enough. Plus some other parts.

Jim you now win the prize enjoy...

Cleaned the gas tank out. New fuel and no gas at the carb. Took fuel pump apart someone had it together wrong. Now it runs like a watch .Thanks for everyone's help !!! What a great forum.

Welcome @Brennanbo. It's nice to see young men doing something constructive with there lives and there's nothing better then working on something that you love doing. I think holding a wrench beats holding a cell phone any day.

Was told by the son of the original dealership owner that arrow sign was given to them from Wheel Horse when they started the dealership.

I have the luxury of working at a place that deals with heavy electrical cables. I can purchase material from work or bring in my own materials and use their crimper to make custom fit cables. This Panduit crimper produces 6tons of pressure.

My name is Paul and I am a WH addict.. I have a problem. I have more tractors than I have needed implements for. I do not swap implements anymore each implement has its own prime mover. So I need some new different implements. So the question what is the most useful non-common (mower deck, snow plow blower) implement that you have. i may need one like it!! (Note my wife's suggestion that I get rid of some excess tractors is a non starter.)

Doesn't need a puller, a couple of 1/4 X 20 bolts will push it out.. Looks like this.

Local parade photos

Make sure the regulator is well grounded. A regulator that has a bad ground can produce over 20 VDC when the grounds connection is broken.

My bad ...bit of American history here EB ...in 1900 Theodore Roosevelt said SPEAK softly and carry a big lunch bucket ....errr big stick! I had to it!

Been wanting to figure out a better way to move dead tractors around - some, just isn't cooperative at being towed - the AC 916H is a great example around here. Since the rear axle is a hydro, it does not disengage fully for some reason and the tires are really shot badly. The 16Auto dug some big holes the last time I tried to move it around, so the idea here is to use the D's 3pt lift and it's size/weight advantage to move other dead tractors. I also wanted a toolbar that could have adapters added for various tasks - such as cultivators, tines, rear blade, ect. I've wanted to build a wrecker for years, just never had the time to do it - this year, I decided I've had enough of my aching back and legs - this needs to get done before I end up in the hospital. Always seems there is no help available when I need it, so now is the time - here is where I'm at as of now... All built from 1/4" thick iron, except the hub mounting plate which 1/2" thick A50 steel. Trailer hub/stub shaft is a 1750lb rated unit. In hindsight, if I ever did it again I'd use a heavier DOM tubing and just turn it to accept bearing races, make the shaft on the lathe and be done with it. Not to mention, I could control the thickness of the assembly a lot better. There are "rear tire carrier builder" parts available out there to do just that with pre-built tubing, the correct bearings and shaft - you just weld it into the square tubing of choice. Still a lot to do - need to make a set of centering springs, locking pins (for toolbar use), tire carrier arms w/tie-down rings, rear blade adapters, ect.... Just thought I'd share a bit - need to some lift testing today, hopefully. Sarge

Thank you it is a pleasure to be here

I’ve had good luck crimping with a heavy old set of tile nippers.

I use my ACCEL spark plug wire crimper (vise and hammer style) on those bigger lugs, I don't use solder and so far for 30+ years nothing has failed me yet.

Picked this up today! Been wanting one for awhile.

The joystick, brake lever, and drive belt tension release look like a 1988 or 1989. The hood looks to be from a later 520H.

Some of the knock off carbs i have I found the float setting to be wildly off 11/64" is correct

Wouldn't want to be without a loader again...

If your aim was better you could have saved setting yourself a mousetrap later....

Heres the lower plate. Didn't turn out too bad either. Don't try this when you're tired or just waking up, make too many booboos.

Several types of crimpers. I go to my local Mennonite auto electric shop and tell them " Make this cable with these ends but go up a size on the gauge." They mount this tool in a vise and wail on it with a big hammer. Then shrink wrap the ends.

Now Jim @WHX20 , employee theft is not nice. Having permission to use a nice Panduit cordless crimper with 6tons of pressure is quite nice though. The cable ends are fairly cheap, the tool to crimp them is not so cheap.

Sorry for the delay I am traveling in California. Happy Birthday my Sipping Friend.

OK, guys, success at last! The temporary setup with the washers worked fine, I was not not completely thrilled with the solution. I feel like it is not addressing the cause, but treating a symptom. So I tried the belt that is 1” shorter. I could not get it on! So I decided to make the best of it, and machined a couple of guides to replace the washer stack. I installed them this evening, and the belt now stays on the pulley. I found in my Dad’s notes ( he bought the tractor new), the notation the main dive belt is 81 7/8” long. I guess the 5L-820 is as close as I will get. I also have no idea where Dad got those numbers... Bottom line is the tractor works as it should, and I am happy! Thanks again for everyone’s help! Danny

I dunno if Dan @Achto willing to give up his secrets EB....... or his employer who has the stuff to have them made professionally..... hey wasn't ther a president who once said walk softly and carry a big lunch bucket?!?!?!?

Just the nature of the Eaton 1100s. I have them in 312s,417s, and a 520 and they all act differently. Like Jeff said, the manual states they should all be warmed up before use. Some of mine require a 5-10 minute warm up before the lift will work and some lift immediately. I chained them all to a tree and they are all strong enough to dig holes.

I have two 520H's. My 1995 starts and the lift immediately works as it should. 320 hrs on that tractor. My 1988 takes a long time for the lift to work. 1000 hrs on this one. When I start it up, I get no lift at all. In about 3-5 minutes, the lift starts working and then continues to work normally for the rest of the day. Both tractors have 10W-30 Mobil One in them and Toro oil filters. Lots of posts on this issue over the years. General consensus - it's just the way Eaton 1100's are.

I have a sundstrand in my C160 and I use mobile1 10w30 and even in the cold of winter the response is immediate. No delay at anytime. I know the Eaton 1100 is bigger and better but it should be almost immediately able to lift and go in the summer time. I do let mine warm up some in the cold only because the manual says to.

Late to the party but still best wishes!

Didn't look to good when I found that Horse. Love it now. I took wheel weights off, polished the baby moons so the Stallion could dress up for awhile.

Best bet is clean the fuel tank and replace all the fuel lines and filter. any auto parts store will have 1/4" fuel hose and filters. Let us know how it works out.

Quite often a digital voltmeter will read all over the place with the engine running. Use an analog meter and recheck. If you don't have one, TSC Lowes ect have them for about 20 bucks.

Must be a U.S.M.C mouse!

same way i do it

Your are looking for pulley # 109967. I have none.

Update... As Ewan has been bogged down by his university work I though I had better put some more pics up of his fab work. we can't get RJ hubs in the UK, so best way is to make them... I gave Ewan a template, which he cut around and we made our own using taperlock sprockets. we welded the studs in to make it easier too... more painting and panel beating! The hood was still in pretty bad condition, but Ewan continued to work his magic!

I'm sure you'll enjoy the ride no matter what hood it has on it! That's the good thing about Wheel Horse's so many parts interchange between models.

Thanks guys .... I remember saying ...now steady big fella....... the eliminator tender was sayin holy $#@% Photo by Dan @Achto Achterberg

I wish Jimmy D was still alive too Steve, he would have liked what the Browns did yesterday. I always liked Cleaveland as well .. my fav underdog team. I always had a penchant for Miami too.... don't know why exactly... maybe because I learned foosball in the Don Shula era.

Many 520s do this and one of mine is no exception. Winter is worse and the colder the worser. My go to snow mover. Sometimes takes a good minute and a half when you can hear the charge pump kick in and begins to whine. No problems during the summer. I switched to Mobile 1 10w-30 syn & NAPA filter and it helped. Next change I'm going to try 5w and see if it makes a difference. This tractor has a peculiar whine to the hydro where my others 1100s don't. No loss of tire spinning power tho. Agreed Jeff ....you wouldn't think so but it seems like they are individual units with a mind of their own. All three of mine act different even tho same oil/filter and linkage setups. I believe it has something to do with how they were treated in a past life or broke in.

I think its just a "multi-tool" that allows you to have a c clamp, wire cutter, pliers and vise grips in one tool... Kinda cool...

Next job was to make some missing parts, the first being the slot hitch. First I cut out all the pieces of steel I needed Cut to size Another part that was missing was all of the clutch set up All welded up Im pretty happy with how it turned out.