Jump to content
IthacaJeff

Loose wheel bearings

Recommended Posts

IthacaJeff

Hi folks:

The wheel bearings in one of the front wheels of my 416-8 imploded the other day while mowing. 32 years old, I'm not complaining. Anyway, with the advice of another thread I picked up a set of 4 flanged bearings off an ebay seller. . .3/4" ID, 1 3/8" OD. Problem is they are a loose fit in the wheel hub. I should need to tap them in, but they just slide in and out. No real play, but they can just fall out. The insides of the hubs are clearly worn.  Any advice on snugging up the bearings"

 

Thanks,

J

Share this post


Link to post
Share on other sites
 
953 nut

I would just take a punch and make a few dimples in each side of the hub. The bearings should need a bit of persuasion then. 

  • Like 5

Share this post


Link to post
Share on other sites
 
N3PUY

Coat the wheel where the bearing goes in with a thin layer of JB Weld and insert the bearing.   It'll be good for another 32 years!

  • Like 2

Share this post


Link to post
Share on other sites
 
JAinVA

I have a piece of pipe in the shop that I drive down on the sleeve and it shrinks the opening to make the bearing a tight fit.The JB weld solution is probably the most cost effective solution.

  • Like 2

Share this post


Link to post
Share on other sites
 
RandyLittrell
Just now, JAinVA said:

I have a piece of pipe in the shop that I drive down on the sleeve and it shrinks the opening to make the bearing a tight fit.The JB weld solution is probably the most cost effective solution.

 

 

The right size impact socket would probably work as well. Drive it over, just like the pipe. 

 

 

 

 

Randy

  • Like 1

Share this post


Link to post
Share on other sites
 
IthacaJeff

I like those ideas. I'll start with the pipe over the sleeve if I can find a pipe the right size. . . .thanks, gents.

Share this post


Link to post
Share on other sites
 
Charles123

Ping  Then over and put loctite green sleeve  Locker

Share this post


Link to post
Share on other sites
 
tunahead72

So @IthacaJeff, how did the pipe work? I have the same problem with my C-105.

Share this post


Link to post
Share on other sites
 
gwest_ca

I had a pair of wheels where the tube split on the inside at the seam in the tube.

Drove a 1-1/2" shaft collar over the tube and then installed new bearings. Worked perfect.

 

Garry

  • Like 1

Share this post


Link to post
Share on other sites
 
IthacaJeff

In the end I used Loctite green sleeve bearing retainer. Seems to be working!

 

Share this post


Link to post
Share on other sites
 
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Jeff_B
      By Jeff_B
      Where's your go-to source for QUALITY 103119 bearing shaft assemblies? Also, I don't have my deck apart yet, but seem to remember they're tough to remove from the housings. Any tips or tricks? Finally, just recently I've had a couple of  the center bearings go loose on two different decks. Once is one thing, but twice? More than a coincidence? Should I be releasing tension on the belt by loosening the mule drive when not in use? We've had WH tractors for over 40+ years and I've never done that before! THANKS in advance! 
    • RichInWalworth
      By RichInWalworth
      Question. I have a 1990 single stage snow thrower for my 312-8. I am trying to replace the bearings on the drive shaft. How do you remove them? I have taken out the set screw, soaked the collar in pb blaster, put some heat to them, pounded on them. etc. They will not move. Am I missing something? The only thing that is curious is, there is only one set screw in each bearing collar. There appears to be a second partially drilled hole but no set screw installed and it does not appear to be tapped. What gives???
       
      Rich In Walworth
    • porschpow
      By porschpow
      Good Morning everybody!
       
      I am in the process of sharpening the blades for my mowing deck (Model 78360 - Serial 7904987) and I noticed that the deck has a crack in it right where the bracket to the mounting hardware (to the tractor) is. SO I know I have to get that repaired.
       
      But while I was at this, I thought I could do a good quick once over on the deck to make sure I am ready for the season.
      What I would like to do is the following:
      Change the bearings for the spindles (or pack them with more grease)
      Get new rear tires (since they squeak)
      And that's about it
       
      If anyone here thinks I should do anything else, I would love to hear it!
       
      Where does everyone get the hardware (bearings, wheels for these rebuilds?)

    • mkueb
      By mkueb
      Does anybody have a good source for replacement front wheel bearings for a mid to late 1970's D160 wheel horse tractor?  There are two push in bearing units (inner and outer) per wheel.   I first attempted to replace with standard bearings but quickly found out these are not standard sizes.   It's been a while since I check and I don't completely remember,  but I think the wheelhorse bearings where something like 1/16" of an inch larger OD than a standard catalog bearing.   At the time,  I remember finding bearings but they wanted somthing like $100 for each bearing.   I was able to located two bearings and did purchase them for a reasonible price,  but am still looking for two for completing the set.   The part numbe ron the two that I was able to locate is 104396.   If anybody has any ideas,  I would appreciate.
       
      Thanks
      Marc
    • Horse playing
      By Horse playing
      Hello, everyone and thank you in advance. I got bit by the bug a few months ago and bought a 1974 b 80  the rod broke, about a month after i bought it. So to keep my 4yr old mowing i picked up a c120 auto and i was going to change rear wheel seals pulled the hub to find the axle moves up and down and side to side about an 1/8"  what's involved in put in new bearing and does it need to be done now or a winter project. Thanks  
       
       
       
               PS sorry about the grammar
×
×
  • Create New...