Jump to content
Sign in to follow this  
dmhill

6 4113 on a 77 B80

Recommended Posts

dmhill

Does anyone know if a 6 4113 plow will fit on a 77 B80?

Share this post


Link to post
Share on other sites
 
gwest_ca

Garry

Share this post


Link to post
Share on other sites
 
dmhill

If I read everything correctly the frame will fit my B80....?

Share this post


Link to post
Share on other sites
 
gwest_ca

Yes it will. Your tractor is a long frame model in 1977.

The long and short frame models are determined by the wheelbase - distance between the center of the front spindles and the rear axle.

Some models are also considered a medium frame which is between the long and the short. I always have to check on the B-Series because I can't remember which models they are.

The 6-4113 has two locations for the rear cross bar in the A-frame that fits into the axle quick hitch to accommodate the different models.

 

Garry

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • mhlmeader
      By mhlmeader
      Hi folks, me and the gal pal were on our way to the wheelhorse motherland ( southbend), to shop for some wedding rings.  So we go down little country road see a barn sale, turned around cause I spy a wheelhorse.  I ask how much , he said 400$, but someone was suppose to be picking it up.  Turns out it came with a sickle bar too. My ears kinda perked up then , cause my dad wants on for his 702.  They call the other fella,  he passed on it, I offered 300$, we settled at 350$. Tractor runs pretty good,  lil smoke when ya goose it, but runs and cuts pretty good.  I'm hoping the sickle bar will fit my dad's 702, it's a 50 inch bar.  Anywho, here's some pics a serial numbers if anyone has some additional info, or point me in the right direction,  would be appreciated,  thanks!!!






    • ebinmaine
      By ebinmaine
      I don't have pictures yet but I can get some later. I know that will be helpful but I forgot to take them last night.
       
      So here's what I know.
      When I bought my c-160 last year it came with a plow. It was delivered to my house and the plow was not mounted on it. I never saw this particular plow on that particular tractor.
      The plow I have is 42 inches wide and has a full frame as most of them do.
      The angle lever has the Z shape to it, NOT a straight stick of metal, and also bends slightly back towards the operator.
       
      When I am pulling the angle lever towards me to change the angle of the plow it contacts the brake lever.
       
      Any thoughts?
       
    • ebinmaine
      By ebinmaine
      I have at least 7 hubs on different tractors that I would like to add a second set screw to.
       
      I have an older but good quality floor model drill press.
      I have the tap set.
      I don't recall ever using the tap set to do anything other than clean out threads. Not make my own thread set.
       
      Can anybody give any particular advice?
    • Goldnboy
      By Goldnboy
      I have a B80 that I acquired from a PO that had the PTO rod shortened and rewelded and the spring removed from the brake pad bracket. I replaced the rod with a non welded adjustable, and reworked the muffler with a 45 so then new rod would fit in. After researching manuals and forum i can only determine that i need to have a 1/8 or less gap between the clutch plate and the bell housing. I can adjust the trunnion all the way in and it seems that some pressure is applied to disk and going all the way out a less is applied. However all pictures i have seen most everyone has the trunnion at least half way up the rod and state that you engage the pto rod with a lot of force, that is not my case at all. Is the stub with the bell housing the problem, it looks like there is plenty of disk plate left.
    • melonman
      By melonman
      Hey Guys, any help with ID or info on this possibly rare bird? It appears to be the original paint but idk for sure. Alo, a B series with electric lift rather rare I think HUH?

×
×
  • Create New...