Jump to content
Geno

Tecumseh engines pronunciation

Recommended Posts

AMC RULES

I hear you bro...my dishpan hands prove...  tumblr_m3nbpcGsNj1qjwbm8o1_250.gif

the most I'm allowed to run around here is the dishwasher.   :) 

  • Like 4

Share this post


Link to post
Share on other sites
 
Ed Kennell

That lucky feline... It's hand washing in the sink only for me.   The dish washer is off limits.   Seems I used the wrong soap one time and filled the kitchen with suds.

 

They never forget.

  • Like 1

Share this post


Link to post
Share on other sites
 
Geno

That's a good way to be banned from kitchen work.  :eusa-whistle:

  • Like 2

Share this post


Link to post
Share on other sites
 
AMC RULES

Putting her cat in the dishwasher on the pre wash setting works pretty good too.   :handgestures-thumbsup: 

  • Like 1

Share this post


Link to post
Share on other sites
 
k+s 1277

tejunkseh!

  • Like 1

Share this post


Link to post
Share on other sites
 
Geno

Better look out or you'll get AMC riled up again.  :laughing-rolling:

Share this post


Link to post
Share on other sites
 
David81

I can't stand it got to get in on this ,,,,,,,,the Kohler  guy's up this way are pretty hard on the (Tecumseh) people as well but dad has a garden  tractor in restore process right now that sit out in the weather for 25 plus years and it has a good old tecky 12 on it after sitting all this time I would have bet at least it would need a carb job but we put a battery in and fresh gas and it started right up and runs like a champ......I say that is a good motor. .......really I like them both   I always pronounced it Tecum sah :scratchead:

Edited by David81
  • Like 1

Share this post


Link to post
Share on other sites
 
buckrancher

Share this post


Link to post
Share on other sites
 
squonk

184479_479609775410697_222476444_n_zpsb8

  • Like 2

Share this post


Link to post
Share on other sites
 
AMC RULES

Looks like Mike killed another one...

yankin' on that govn'er again.   :eusa-doh: 

          indian-1.gif

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • ebinmaine
      By ebinmaine
      A HUGE thank you to Tony @Docwheelhorse for settin' me up here.
       
      The generosity of some of our members never ceases to amaze me.
       
      This here is another 1974 C160, but with the rare Tecumseh HH/OH160 OHV engine. Made one year only.
       
      It's rough. Very much in need of a full disassembly and restoration.
       
      When it came here it was missing one tie rod and the other was broken off one end.
      Today I popped used tie rods on and Trina used her 867 to drag it from the drive to the shed.
       
      The engine wouldn't move.
      Tin was near chock full of skeletal mouseseses and their house.
      Cleaned that out and the engine spins freely now.
       
      So progress has been made.
       
      It'll be a good long while before we get to this one but I just couldn't turn it down considering the rarity.
       
       




    • Nathan
      By Nathan
      Can anyone help finding year of this tecumseh motor off a 603. I need a carburetor.


    • ebinmaine
      By ebinmaine
      We're going to take apart the Tecumseh from my Honey's 657 so I can replace the crankshaft.
      Any little tricks or tips I need to know about?
    • ohiostate454
      By ohiostate454
      So I have been working on a 656 I picked up at the end of last year and I did my first ever motor rebuild by my self on it. However it seems that I have lots of play in the piston and some slop at TDC more then I should have. So to finish the year mowing I am thinking of doing a predator swap while I go over the engine again. I am sure several people have done this before and I have a spare mounting plat to make it work. I am wondering if anyone has any pictures of ones they have done for help along the way. I know I will need a adapter to use the factory pulley and I don't want to destroy any of the sheetmetal since it is in good shape. I will keep you posted as I go along and eventually when I get the hh60 back together correctly to re install.
    • ebinmaine
      By ebinmaine
      I've ordered this set
       
      https://www.redoyourhorse.com/tecumseh-4-pc-engine-decal-set/
       
      from our awesome vendor Terry @Vinylguy.
       
      I know where the balloon sticker goes and the oil sticker.
       
      Where does the large "Solid State" one belong??
       
      Thanks!!
       
×
×
  • Create New...