Jump to content
Rayp

Hi, I'm Ray from Cheltenham England

Recommended Posts

Anglo Traction

Ray,

       I'm pleased that your now able to post Pics. :hide: It was not intended by me to force your arm up your back to become a Supporter ! (maybe I should sell Insurance! :D ), but more than pleased that you have turned Red  :eusa-clap: .

 

It may be worth checking to see if you have adjustable settings for Pic size on your camera etc. I have set mine to E-mail size, which produces pics of about 850kbs. Reasonable image, but the site dumbs them down in the post anyway to about 300kbs......check it out.

 

Seat has had a hard life, but original,  keep it if you can.

Regards.

Share this post


Link to post
Share on other sites
 
Wheel-N-It

Thank you for becoming a Supporter Ray!

Share this post


Link to post
Share on other sites
 
Jparkes43

Hello nice to see a fellow englishman here 

 

James 

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • BrianStasC-101
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
    • RJ Hamner
      By RJ Hamner
      Will the plow I am using on my C121 and C160 work on a 876?  
      or is the plow frame different?
      Thanks
      Bob
    • drewd
      By drewd
      Hi All,
       
      I have what I believe is a Commando 800 but would like to confirm model and year.  Tag reads Model # 1 0100 6; Serial # 790336. Have had it for years (bought from original owner) and want to clean it up some.
       
      Thanks!

×
×
  • Create New...