Jump to content
wheel-mule

20 hp Kohler Commamd

Recommended Posts

wheel-mule

When it comes to wiring I'm not the brightness blub in the box.I need help.I bought a 20 hp command engine.What do I have to do to wire this thing up?It's going on a pulling tractor so there is no saftey switches to worry about.There is a plug on the side of the engine.One wire from the plug goes to the solenoid.What switch do I need (I know they look the same but the terminals/spades are different) and which wire(s) do I hook to in the plug..

Edited by wheel-mule

Share this post


Link to post
Share on other sites
 
Jeff-C175

What model WH machine are you installing this on?

Share this post


Link to post
Share on other sites
 
gwest_ca

Just added the Kohler service manual. Electrical starts on page 32. I have one and it has magneto ignition. You will need to identify what ignition system you have as there is more than one.

 

 

Garry

Share this post


Link to post
Share on other sites
 
wheel-mule

I'm putting it on a Lawn Ranger. The engine is a model CH20S

Share this post


Link to post
Share on other sites
 
boovuc

A 20HP Twin in a Lawn Ranger???????

Share this post


Link to post
Share on other sites
 
wheel-mule

It has  9x3.50 x4 smooths on the front and 20x10x10 smooths on the rear.Front axle from a 212-5 with 1/2 milled off to lower front more.

Share this post


Link to post
Share on other sites
 
boovuc

OK. So we won't be mowing with this horse!

Share this post


Link to post
Share on other sites
 
wheel-mule

Pulling tractor mainly dead weight but may do some transfer sled pulling

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • BrianKoch
      By BrianKoch
      Hello gentleman, 
       
      Problem: will not crank on its own, will crank with jump box—but still not fire
       
      Recent things I did prior to this issue: cleaned fuel filter, replaced battery cables, replaced cable from ignition to starter
       
      I have my test light out and am probing around. 
       
      There is no power at ignition/magneto wire or the ignition/starter wire
       
      There is power everywhere else






    • Jeff-C175
      By Jeff-C175
      Detailed wiring from the Demystification Guide #492-4509
      4 pages 1.4MB Color
      p7-67 to p7-70
       
      Onan powered
       
      1989 416-8 model 31-16O801
    • trident
      By trident
      Need some help. My 800 Special has an electric PTO. It is not working. Checked Ohms - nothing. My questions are 1) how does the PTO come off and 2) can they be rebuilt? I took the bolt out that I thought holds it on but no luck. Must be something more?
    • grasscuts
      By grasscuts
      Hi, here's what happened. I changed out 9 pin moles plug...had issues tracter quit running and changed the plugs while I was at it....got plugs from auto store cross reference to ngk they said it was the same heat range and I check electrod  length with calipers ,same...tracter started right up and ran great for about 10 min. And started back firing and quit.....going to check it out tonite anybody have an idea?    
    • jakester
      By jakester
      hello all I'm a new owner of a 312-8 tractor, have starting problems, came across a very small, what I believe is a relay between the battery and the dash,its about 2/3rd size of a cube of sugar silver on the outside blue on top with a hole bout the size of a pea, theres 6 pins with wires connected to it on the bottom do not know what this is any thoughts? I cannot determine the exact year of this machine for there is no tag anywhere only tag on engine kohler magnum md #m12s   ser# 170370459  spec#  471527  I figure its mid to late 80s to early 90s. of all the wiring diagrams ive looked at it does not show any thing like what I just described also can that little circuit board be removed that's like a test point for idiot lights? any help would be appreciated  jeff
×
×
  • Create New...