Jump to content
Sign in to follow this  
Hydro

414-8 OHV

Recommended Posts

Hydro

I have an opportunity to buy a low hour 414-8. I had heard those first OHV engines introduced in 1998 were not as good as the Magnum and K series. Does anyone have any comments one way or the other?

Share this post


Link to post
Share on other sites
 
Forest Road

I had a 2001 12.5 in a 312-8. It was abused to say the least. Ran well after a tuneup. The PO stripped the fuel pump mount in the aluminum block. We helicoiled it and it seemed fine. I sold it to a friend two years ago. He loves it! I personally prefer the thump of a flat head kohler. However given the chance to grab another Command OHV Id probably jump on it. Newer tractor and little more fuel efficient motor.

Share this post


Link to post
Share on other sites
 
Wheel-N-It

Gary, all I can do is comment on your inquiry. I've known for a long time that overall Kohler makes a good engine. I'd say if you like the tractor, and the price is right, and you got the money, then buy it. Heck if its been running however many hours, and the engine sounds good, and its been taken care of, then chances are it will serve you well just like it did the previous owner.

Just my 3cents,

Van

Share this post


Link to post
Share on other sites
 
kpinnc

And if the motor blows, You can always replace it with K321s, M14s.... :)

Share this post


Link to post
Share on other sites
 
CRE1992

414-8s were only made in the mid to late 80's and had K321 and 14hp magnum engines... So either the engine was replaced or you have the wrong model number...

Share this post


Link to post
Share on other sites
 
kpinnc

But the later year model 314-8 had a Kohler Command 14 on it, which may be what Gary has found.

Share this post


Link to post
Share on other sites
 
BOWTIE

HELLO GARY, I MOW WITH A 1999 314-8 KOHLER OHV. THIS WAS MY FIRST OHV ENGINE. PLENTY OF POWER AND QUIET. I HAVE BEEN USING IT FOR ABOUT 5 YEARS NOW. HAVING A OIL FILTER THE OIL STAYS CLEAN FOR A VERY LONG TIME. I CHANGE OIL EVERY 50 HRS AND FILTER 100 HRS. THE MANUAL RECCOMENDS YOU GO LONGER. THE OIL IS 10W30 AND A COMMON SPIN ON FILTER. I LIKE IT JUST MY TWO CENTS.

BOWTIE

Share this post


Link to post
Share on other sites
 
Hydro

Thank you all for your input. I have no experience with this engine. This unit has a snow cab mounted so I can't see the model number but it is post 97 and it is the first generation of the OHV before their 15HP. I checked the models on this site...1998-2001 if I recall correctly.

Share this post


Link to post
Share on other sites
 
tgranthamfd

I can't speak on the 14hp OHV's, But I can tell you about the 15hp OHV Kohler Command's. They are very powerfull, reliable, and fuel efficient. Mine is a 2005 315-8, and it is my go to tractor for anything I could throw at it. For the last 2 years it has been my plow, grader, box blade, and tiller tractor. I decided to throw the deck back on it the other day, and it still mowes like a dream, and I can put a gallon of gas in it and mow my yard 3 times before it needs to have more, I don't have a small yard either. I would not trade it for anything, but it has been kept inside and clean for it's hole life, and properly maintained as well. Heck, I expect it to out last me. p.s. it is the one in my avitar, but it has chains and weights on it now. didn't mean to ramble on so much.

Share this post


Link to post
Share on other sites
 
Hydro

I can't speak on the 14hp OHV's, But I can tell you about the 15hp OHV Kohler Command's. They are very powerfull, reliable, and fuel efficient. Mine is a 2005 315-8, and it is my go to tractor for anything I could throw at it. For the last 2 years it has been my plow, grader, box blade, and tiller tractor. I decided to throw the deck back on it the other day, and it still mowes like a dream, and I can put a gallon of gas in it and mow my yard 3 times before it needs to have more, I don't have a small yard either. I would not trade it for anything, but it has been kept inside and clean for it's hole life, and properly maintained as well. Heck, I expect it to out last me. p.s. it is the one in my avitar, but it has chains and weights on it now. didn't mean to ramble on so much.

It's ok you're in love :wub: Thanks for your input.

Share this post


Link to post
Share on other sites
 
SAM58

I have a 1998 314-8, it has become my favorite tractor for grading or general work beside mowing, over my 520H.

I too was leary of the OHV engine until I used it for a while, it is a very good engine.

UPDATE....

i JUST NOTICE HE SAID HE FOUND A 414-8 WRONG ANSWER.

I WOULD SAY IF IT HAS THE OHV - IT IS A 314-8.

MINE IS THE 1998 AND I REALLY LIKE IT, QUIET, PLENTY OF POWER.

WHEN YOU PUT IT UNDER A LOAD YOU CAN HEAR THE OLD KOHLER THUMP...

Share this post


Link to post
Share on other sites
 
can whlvr

i think if its a 314 gary of that late of years it will have the heavy rear and 8 fronts,which is basically a newer 414,which i have 2 of and really like em,they are great machines,but yours would be alot newer and even more refined one would think

Share this post


Link to post
Share on other sites
 
Hydro

Hey Guys...sorry about the model confusion....I got my murds wixed. It is a 314-8 not a 414-8. It has the OHV engine and sounds like people who know them have had no problems. This is a tractor I don't need but might buy only because....I'm sure many of you know what I mean!

Thanks for the input, much appreciated :flags-canada:

Share this post


Link to post
Share on other sites
 
can whlvr

gee gary i better watch out or your gonna pass me in the #,s area,if its a good deal you can allways get your cash back,or usually anyway by the prices i see up here,last week a similar machine to what your talkind theyy were askind 2500

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • Hydro
      By Hydro
      I recently bought a 1994 tall chute single stage snow thrower, model 79360.  I have replaced the chain, both idler sprockets, both idler pulleys and one jack shaft bearing on the chain side.  The auger is strait and the bearings are smooth.  It runs quietly.  I have it mounted on my 314H powered by a Kohler M16.  I am shearing the pulley key on the jack shaft.  It has happened twice now.  The first time it threw the set screw so I thought it was a matter that the screw was not tight enough.  Toro shows one screw although the pulley is drilled and tapped for two.  I was careful I thought when I positioned and tightened that screw.  After the first time, 20 minutes running, I added the second screw.  I also noticed the pulley has some wobble to it so I used some shim stock in order that there would be no play between the shaft and the pulley.   I ran it for about 20 minutes again and noticed both screws were loose so I used Loctite 242.  I let that sit for about 30 minutes and went out again.  In about 20 minutes I sheared the new key right off with a portion of it in the keyway of the pulley.  The shaft is clear of the key but has been scored some.
      My driveway is paved.   I was plowing before and built up some snow banks.  The first time I sheared the key, the thrower was mainly resting on the scraper blade and I was just removing snow from the driveway, I thought I might have jammed it with some ice.  The second time I raised the thrower to give it clearance so there was about 3/8†between the blade and the runners which I adjusted.   
      I ease the machine into snow and creep along.  I do not ram it into snow banks.  I’ve seen videos of these things working really well.  Mine was blowing snow beautifully but something is not right.  Is it the fit between the pulley and the jackshaft?   Why would Loctite not hold the set screws? What is wrong with my machine or what I’m doing wrong?
      I have to suspect there is a weak point where something will give or the belt will just slip.  My belt is new and has the correct Toro Part number.  It fits the way I have seen them mounted so I doubt that has any part of what is happening.
      I would appreciate your thoughts. 
      Thanks
      Gary
    • Hydro
      By Hydro
      I've been reading through various chain & bearing repair posts regarding the snow thrower.  I have just acquired a 1994.  The auger, jack shaft bearings and drive sprocket are in good shape.  The blower needs idler pulleys, a chain and the inside sprockets.  The auger sprocket rotates with about a 1/4" of wobble and the teeth are getting sharp. Is it normal for the auger sprocket to be off a little when manufactured?   The auger itself runs true.  Not sure how far to go with the rebuild as I know the auger sprocket would have to be re-done at a machine shop.  Here are a couple of pictures of the sprocket teeth.  What do you think?
       
      Thanks for your time.


    • Martin
      By Martin
      trying to determine whether i have a good trans or not and have a question or more.
      i have an eaton 1100 in a rolling chassis that i want to test to see if its working well enough to justify using in a new tractor rebuild. i hooked it up to my 1848 pto with a longer mower belt to test it out. oil looks very clean so i left it and i know i need to get the correct filter on there, but for now its staying until i see some light at the end of the tunnel.
       

       

       
      just did a quick test tonight to see if i could at least get the lift to work. success on the first pull of the lever. hydro pump seems very quiet and no leaking or damp areas either. i worked the lift up and down from one extent to the other and it worked as good as any nice working lift i have. so I'm happy so far, now the questions......
       
      to test the drive I'm going to get it up off the ground and see if i can get the wheels to turn in either direction. i want to run it this way for quite a while until i can get some raising of oil temp. 
       
      is putting weight on the lift going to change anything as far as a test goes? i figure if it goes up and down, is quiet doing so and doesn't leak, I'm 99 % there....
      is there any way to check to see if it is loosing pressure when it gets warmer?
      can a gauge be hooked up and is this easy enough to do?
      is it even worth finding out the pressures? what will having them tell me?
      is this a good enough way to test the whole hydro system? i think it will tell me at least if its working and if there are any leaks. i don't have a working engine that i can just throw in there to drive it around without puling one of my old starter gen motors from an unrestored 1277. i know this is probably the best way, drive it and get it nice and hot to be sure. i could swap it out from one of the other 1100s but then i got to deal with hoses etc and not really interested in pulling apart good working systems and opening other cans of worms.
       
      while it was running, and over the noise of the engine in the 1848, the pump seemed to be very quiet, quieter than the other 2 1100 tractors are. both of the other 1100s work well and aside from one having a leak in the lift, they both are leak free. 
       
      ao at this stage i am happy with how things are going. just wondering if there was some expert opinions to help me on my way with some ideas.....
       
      thanks in advance for any input, fire away guys.....   
    • FZR
      By FZR
      Does anyone know where I can get a Routing Diagram for an LT-1100 3-Speed Drive Belt.  I'm looking for the routing diagram for the drive belt that runs from the engine to the transmission.  Any help would be appreciated. 
    • B-8074
      By B-8074
      Will a tiller for a 5xi work on my C-175 without having to do any modifications?
×
×
  • Create New...