Jump to content
  • Please Read

    The classifieds are for MEMBER equipment only. Please do not post links to ad's or auctions on other hosted on other sites. Any such postings will be deleted. Posting of any comments other than questions regarding the ad will be removed without notice.  Please help us keep the classified section on track.  If you are posting an item for sale you MUST include your location and a price. Items posted without a location or price are subject to removal. You may NOT auction an item to the highest offer. RedSquare is not responsible for the accuracy of the listings. First and foremost, "make all deals at your own risk" and "settle all disputes off of the forum". It is your responsibility to validate the legitimacy of the seller and the sale.  You may report a failed transaction to the moderator administration team which will be evaluated for repeat offenders.  Any effort to deliberately deceive or defraud members will result in expulsion from the forum.

    Do not post duplicate ads in an attempt to increase visibility, any duplicate posted will have newest ad removed, continued posting of duplicate ads will result in suspension.

     

    Hint use the filter on the right to only see active posts. Closed posts indicate the item is no longer available.

     

  • PARTS...PARTS...PARTS 30+ Years accumulated


    daveoman1966
    • Active
      Price: 1
      Location: N/w Pa.. Zip 16433 40M South Of Erie Pa
      Contact: Dave (daveoman66)

    For 30+ years, I've accumulated a TON of used Wheelhorse parts and am now retiring (again). Hate to scrap all of this as many of you guys may have use of parts.  I have 80 or so pics, but can't list all of that here.  Yet, here are a few. 

    Come one..come all.  Bring truck / trailer / helper....and cash. 

    NOTE... many have asked me for vintage parts like for a,  502, 702, etc.  I don't have any parts to fill those needs... The parts I have begin from late 60s...67, 68...up thru the 520H models.  Sorry... I should have been a little more specific... 

     

    002.JPG

    003.JPG

    005.JPG

    011.JPG

    012.JPG

    014.JPG

    015.JPG

    031.JPG

    035.JPG

    045.JPG

    059.JPG

    061.JPG

    062.JPG

    065.JPG

    066.JPG

    067.JPG

    069.JPG

    070.JPG

    077.JPG

    088.JPG

    090.JPG

    093.JPG

    096.JPG

    098.JPG

    310-8 pts (2).JPG

    • Like 5
    • Excellent 1


    User Feedback

    Recommended Comments

    Looking for a pto clutch disc for 308-8. Id like to have 2 if you have them. Price please if you do have them, thanks in advance, Brady.

    Share this comment


    Link to comment
    Share on other sites

    interested in 42" side discharge mower.  Call or text 440-520-0058

     

    thanks   tim

    Share this comment


    Link to comment
    Share on other sites
    7 hours ago, WHX20 said:

    Have a left side axle for a 520 - Eaton 1100?

    I have the one like this that is 13 1/8" long..  (#13)  also have one that is 11 5/8" long (# 11)  that can be cut to the 10" length for 520, then plunge cut a ley slot on other side.

    $55...13" length

    $25...11 5/8 length to cut down to 10" length for the 520

    These are all 1 1/8" axle dia's

    Ship via USPS medium FRB...$15 to any USA zip code.

     

      

    520ax 001.JPG

    526.JPG

    Share this comment


    Link to comment
    Share on other sites
    3 hours ago, WHEELHORSEFAN3 said:

    Looking for a pto clutch disc for 308-8. Id like to have 2 if you have them. Price please if you do have them, thanks in advance, Brady.

    Ebay has some new ones....usually, that is.  I have none.

    Share this comment


    Link to comment
    Share on other sites

    Any 3/4" keyed spindle assemblies - the kind with the grease fitting on top?

     

    The housing on one of my spindle assemblies cracked in two places, and I'd love to not have to buy a whole new assembly + pulley + have a different blade (in other words, I'd love to stay with the 3/4" style).

    20180813_112127.jpg

    Share this comment


    Link to comment
    Share on other sites

    I have one that is good shape, except for 1 of the 4 mounting holes is stripped out.  Use this 3/8 bolt instead.  The seal is ruined and the top bearing is probably shot...I will include this replacement bearing in useable condition.  $55 w/out the spindle shaft shown.  $35 for the shaft.  Threads on it and the key slot are very good.  also have the CENTER PULLEY...$35 for it..if needed.  

     

     

     

    spin used (9).JPG

    spin used (8).JPG

    spin used (4).JPG

    spin used (3).JPG

    Edited by daveoman1966

    Share this comment


    Link to comment
    Share on other sites
    On 8/14/2018 at 4:02 PM, WildmanC120 said:

    Do you have a K341 that's complete?  What about the hydo lift setup usually need on a C-160?

    I have the CONE and SPRING that is needed for the Hyd pump End Cap.  Also have four hydraulic lines ??? that should fit, and the Control Valve (A or B in pic).  Whats lacking is the Hyd cylinder and the rock shaft (replaces lift handle).   

    LIFT VALVES-15.jpg

    lift syst-15 - Copy.jpg

    cyl (3).jpg

    Share this comment


    Link to comment
    Share on other sites

    My address is:  

    16729 Price Rd.

    Saegertown, PA..  16433.  

    About 10 miles East of Meadville, PA.

    Share this comment


    Link to comment
    Share on other sites

    Me thinks belt is # 9750 which is 5/8 x 69".  I do NOT have that belt.  I SO have a set of dolly wheels for the side of it....should fit ...just drill a hole in either side of the housing.

    These HARD rubber wheels are 3 3/4" diameter and 1" wide with mounting shoulder bolts & nuts.  I can put them in your USA mailbox for $18...SHIPPED.  I use Paypal.    

      

    dolly wh 002.JPG

    dolly wh 001.JPG

    Share this comment


    Link to comment
    Share on other sites

    I'm in need of a hydraulic cylinder 8in.long the cylinder it is on a

    C-520

    Edited by oneroadkingman

    Share this comment


    Link to comment
    Share on other sites

    I'll add my request!

     

    Do you have the oil fill tube (KOHLER 47-029-06) for a 312?

     

    Thanks!

    Dave

    Share this comment


    Link to comment
    Share on other sites

    I have several oil filler tubes here....  from 520, 416, 417, C-160, C-145 etc.  

    You have a pic of it...and the length?  

    Is this a312-8 or a 312-A or 312-H???

    I have a 314-A tractor, Eaton 700 trans and will size that against what you need.

    Here is a pic...

     

    dip 009.JPG

    Edited by daveoman1966

    Share this comment


    Link to comment
    Share on other sites
    On 8/26/2018 at 4:32 PM, daveoman1966 said:

    I have several oil filler tubes here....  from 520, 416, 417, C-160, C-145 etc.  

    You have a pic of it...and the length?  

    Is this a312-8 or a 312-A or 312-H???

    I have a 314-A tractor, Eaton 700 trans and will size that against what you need.

    Here is a pic...

     

    dip 009.JPG

    The one I need is for a 312-8. This one has a type of flange at the bottom with 3 screws holding it to the engine. i can have a picture of it in a couple of hours.

    Share this comment


    Link to comment
    Share on other sites

    ok...post a pic or 2 & I'll try to match it...  The dipsticks above are for Transmission...not engine

     

     

    Share this comment


    Link to comment
    Share on other sites

    Dave, would you have a headlamp bucket to fit mid 70s WH tractors?  I have the front transparent cover plate, but am missing the bucket that holds the bulbs.  Thanks.

    Share this comment


    Link to comment
    Share on other sites

    looking for the following for a raider 10: 

     

    drawbar 

    one or two front wheel spindle (left at least and possible right)

    parking brake lever

    possibly belt guard if you have them.

     

    thanks

     

    Edited by SimonC

    Share this comment


    Link to comment
    Share on other sites

    $25..darwbar w/out pin  (TSC HAS pins)

    $25   Lt and Rt spindles (wheel held on by 3/8 bolts OR by C-Clips...either set)

    Park brake lever...not sure what you mean...  

    $20...belt guard.

    Can you send a pic of the brake lever you need, and the belt guard too.  I ahve several belt guards from different older tractors...

     

     

    Share this comment


    Link to comment
    Share on other sites


    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now


  • Recently Browsing   0 members

    No registered users viewing this page.

×